Lynx Dollhouse 1000-300-011-V0 User Manual download pdf (Page 2)

Programming Notes

Entering Voice Prompt Programming

Power-up the control and enter the Installer Code + 8 8 8.

When you have completed each programming procedure

the system will return to the Main Programming Menu.

Exiting Voice Prompt Programming

Once you have returned to the Main Programming Menu,

press the ESCAPE/ OFF key.

Entering Central Station Phone Numbers

Enter 0-9, #+11 = 7, #+12 =#, #+13 = a pause of 2

seconds.

Entering Central Station Account Numbers

Enter 0-9, #+11=B, #+12 =C, #+13=D, #+14=E,

#+15=F

Programming Zone Types

The Voice Prompt Programming feature can not be used to

program Zone Types 02, 05, 10, 14, and 24. Programming

these zone types must be done using the Expert

Programming Mode.

5. Voice Prompt Programming

Navigating the Voice Prompt Programming Mode

Scroll through the voice menu and follow the instructions provided to

continue using the Voice Prompt Programming Mode.

The following keys are used to navigate through this feature.

1. ESCAPE/ OFF key: Used at any time to exit the current menu and return

to the previous prompt.

2. ADD/ AWAY key: Used to add sensors or keys or save data when

entering phone or account numbers.

3. DELETE/ STAY key: Used to delete a sensor when in the delete

Sensors Menu.

4. SELECT/ AUX key: Used to confirm a selection.

5. 3 ↑ key: Used to scroll forward through menu choices.

6. 6 ↓ key: Used to scroll backward through menu choices.

7. FUNCTION/ # key: Used to repeat a voice prompt.

(This function cannot be used while entering phone or account numbers.)

1000-300-012-V0

ARMED READY

BYPASS

NO DELAY

RECORD

TEST

FUNCTION

STATUS

VOLUME

PLAY

CODE

LIGHTS ON

LIGHTS OFF

CHIME

ESCAPE

ADD

DELETE

SELECT

1 2

4 5

OFF

AWAY

STAY

AUX

6a. Add Sensors

The Lynx Plus Series will enroll a sensor once the transmitter has been activated two times. The system will confirm the enrollment

following each subsequent activation of the same transmitter.

Add a Door Sensor

(1) Delay Door Location

Front Back Side Garage Basement

Sliding Hall Kitchen Patio

Add a Window, Motion Detector, or Fire Detection Sensor

(2) Sensor Type (3) Sensor Location (4) Location Modifiers

Window

Living room

Kitchen

Family Room

Attic

Upstairs

Second Floor

Motion Detector Dining room Hall Guest Room Office Downstairs Front

Fire Detection Bedroom Basement Laundry Room Upstairs First Rear

Bathroom Master Bedroom Utility Room Second Side

Nursery Den Garage Third

6a. Add Sensors (Continued)

Add an Emergency Pendant

(5) Pendant Type

Medical Fire Silent Police Police

Add a Wireless Key

When adding wireless keys, wait 5 seconds between

transmissions.

6b. Delete Sensors

Delete Sensors

7. Add Central Station Accounts

Add First Central Station Phone Number

Add First Central Station Account Number

All four digits of the Central Station Account numbers must be

entered. For ten-digit format, all ten digits must be entered.

Refer to the Lynx Plus Series Installation and Setup Guide for

additional information regarding these programming options.

Add Second Central Station Phone Number

Add Second Central Station Account Number

8. Program Additional Options

Enter Expert Programming Mode

Once you have entered the Expert Programming Mode, the

[ESCAPE] key can be used to return to the Voice Prompt

Programming mode. If you are in any of the Interactive Menu

Modes (756, 780, 781, 783, 784 or 785), you must return to

the main menu in that field before pressing the [ESCAPE] key.

The Lynx Plus Series is configured with Factory Default Settings. You

can revise these settings using the Expert Programming Mode. Refer

to the Installation and Setup Guide to view these defaults and to

continue programming the individual fields using this mode.

Exit Expert Programming Mode

When programming is complete, enter 799.

9. Perform Go/No Go Test

Temporarily mount wireless devices in the preferred mounting

location and perform a Go/No Go test to ensure adequate signal

strength is available.

1. Enter Installer Code + [#] + [8] and run Go/No Go Test.

2. Fault each transmitter to ensure all programmed zones are

received.

3. Mount the transmitter in its permanent location.

10. Program User Functions

Set the Real-Time Clock

1. Enter the Installer Code + FUNCTION/ # + 63

2. Follow the Voice Prompts to program the Clock/Calendar.

Change the Master User Code

1. Enter the Installer Code + CODE/ 8 + 02 + desired 4-digit Master

Code.

Add User Codes

1. By following the procedures in the Lynx Plus Series User Guide,

show the User how to add additional User Codes.

11. Test the system

1. Enter the User Code+ TEST key. The external sounder will sound

for two seconds and all the LCD segments on the keypad display

light for 3 seconds.

2. Open each protected door and listen for three beeps from the

keypad, followed by the zone’s Voice Descriptor. Identification of

each faulted protection point should appear on the display, and

clear when the door is closed.

3. Walk in front of the motion sensor and listen for three beeps and

the zone’s voice descriptor.

4. When testing is complete, enter: User Code + OFF key.

5. Press each key on the key fob to confirm it performs its assigned

function.

Note: Refer to the Lynx Plus Series User Guide for additional information.

1 2

Ê800-03860/Š 1
1000-300-012-V0 2

Comments to this Manuals

No comments

Lynx Dollhouse 1000-300-011-V0 User Manual Page 2

Comments to this Manuals