Lynx Dollhouse 1000-300-011-V0 User Manual download pdf

Lynx Plus

Lynx PlusLynx Plus

Lynx Plus Series

Series Series

Series Control

ControlControl

Control

Quick Installation Guide

This Quick Installation Guide can help you install the rechargeable Lynx Plus Series Control quickly and easily by providing the

basic steps for installation using the built-in defaults and the Voice Prompt Programming mode. The Voice Prompt

Programming mode allows you to quickly program the system by responding to a series of voice prompts.

FOR DOCUMENTATION AND ONLINE SUPPORT: http://www.security.honeywell.com/hsc/resources/MyWebTech

(see Lynx Plus Series Installation and Setup Guide P/N 800-03857 or higher)

WARRANTY INFORMATION

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa

1. Install the Control

1000-300-011-V0

FRONT

CASE

MOUNTING

HOOKS

LOCKING TABS

BACK

CASE

ROTATE

FRONT CASE

UPWARD

TO RELEASE

HOOKS

GSML/GSMVL

COMMUNICATIONS

PORT

GSMVL AUDIO

CABLE CONNECTOR

BATTERY

CONNECTIONS

PLCD

CONNECTOR

TELEPHONE

CONNECTION

2. Make Wiring Connections

UL NOTE

THE MINIMUM WIRE SIZE USED FOR TELEPHONE

INSTALLATIONS MUST BE #26 GAGE

WARNING

TO PREVENT

RISK OF SHOCK,

DISCONNECT

TELEPHONE LINE

AT TELECOM

JACK BEFORE

SERVICING

THIS UNIT

1000-100-004-V0

NOTE

USE ONLY THE

K10145WH/K10145X10

OR K10145CN

TRANSFORMER

PROVIDED

PREMISES

TELEPHONE

INCOMING

TELEPHONE

LINE

PIEZO

6-14VDC

120mA max.

6-14VDC

30mA max.

BELL

PHONE

ZONE

SOUNDERS

EARTH

GROUND

K10145WH/K10145X10

OR K10145CN

PLUG-IN

TRANSFORMER

9VAC, 25VA

RING

TIP

RING

TIP

INCOMING

PHONE

LINE

8

POS

JACK

SOUND

OUT

HWZ

ALL OUTPUT CIRCUITS ARE POWER LIMITED.

HARD

WIRED

ZONE

2k

OHMS

EOLR

EARTH

GROUND

Note: For the complete Summary of Connections, refer to the Lynx Plus

Series Installation and Setup Guide P/N 800-03857 or higher

3. Make Battery Connections

1000-300-007-V0

BATTERY PACK

NOTE

WALYNXRCHKIT-SHA

BATTERY PACK SHOWN

RETAINER

SCREW

4. Program the Control

Change the Installer Code

The factory default Installer Code for the Lynx Plus Series Control is set

to 4-1-1-2. To change this code, you must enter Expert Programming

mode.

1. After Power-up, enter Installer Code + 8 0 0 or press both the [7]

and [#] simultaneously within 50 seconds after power is applied to

the control. The system will enter the Expert Programming Mode

and “20 INSTALLER CODE” will be displayed.

Note: Upon power-up or after exiting program mode, the system takes up

to a minute to reset. To bypass the reset delay, enter [#]+[0].

2. Enter 720

3. Enter a new four-digit Installer Code.

Program variable data fields

1. If required, enter 724 to program the desired 2-digit RF House ID

for wireless keypads.

2. If required, enter 740 to program a PABX Access Code or to

Disable Call Waiting (LynxSIA Plus only).

3. Enter 794 to program the downloading computer phone number.

4. Press the ESCAPE/ OFF key to enter Voice Prompt Program

mode. The system will announce, “Programming, use arrows

to scroll

choices, press select to accept, press escape to quit.” The system

will announce the available options.

1. Separate the front case from the rear case by rotating the front

case and releasing the hooks from the rear case.

2. Feed the wiring through the openings provided in the rear case.

3. Mount the rear case to a sturdy wall and secure with the provided

screws.

3. Reconnect the front case and rear case.

1. Make earth ground connections to terminal 1.

2. Connect the incoming phone line to either the 8-position jack or

terminals 2 (TIP) and 3 (RING).

3. Connect the handset phone lines to terminals 4 (TIP) and 5

(RING).

Note: For full line seize operation, refer to the Lynx Plus Series

Installation and Setup Guide.

4. If used, connect a piezo sounder or bell to terminals 8 (-) and 9

(+).

5. Connect the sensors/contacts to the hardwired zone terminals 6

(-) and 7 (+).

6. If used, connect the GSML or GSMVL communications device to

the GSML/GSMVL communications port.

7. Connect wires from the K10145WH/K10145 OR K10145CN

Transformer to terminals 10 and 11.

Note: If using Powerline Carrier Devices refer to the Lynx Plus Series

Installation Guide P/N 800-03857 or higher.

1. Remove screw securing the battery retainer.

2. Remove the battery retainer.

3. Insert battery pack into back plate.

4. Install battery retainer.

5. Install screw to secure the battery retainer.

6. Connect battery connector to receptacle on PC board.

7. After all wiring connections have been made, snap the front

assembly to the back plate so it is held by the locking tabs.

8. Plug the transformer into a 24-hour, 110VAC unswitched

outlet.

Note: Rechargeable batteries may take up to 48-hours to fully

charge. “LOW BAT” message should clear within four hours,

or by entering Test Mode.

5. Follow the directions provided by each voice prompt to make your

selections.

The FUNCTION/ # key can be used to repeat a voice prompt,

as required.

6. When you have completed each programming procedure the

system will return to the Main Programming Menu.

Viewing data fields

1. To view data entered in field, press [#] plus the field that you wish to view

(e.g., #21). The system will beep three times and data programmed for that

field will be displayed to the right of the field number. The system will scroll

through the data for longer numbers and a beep will sound after each

number is displayed or three times after the final digit is displayed.

(Continued on reverse side)

Ê800-03860/Š

800-03860 9/09 Rev. A

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

1 2

Ê800-03860/Š 1
1000-300-012-V0 2

Summary of Contents

Page 1 - Ê800-03860/Š

Lynx PlusLynx PlusLynx PlusLynx Plus Series Series Series Series ControlControlControlControl Quick Installation Guide This Quick Installation Gui

Page 2 - 1000-300-012-V0

Programming Notes Entering Voice Prompt Programming Power-up the control and enter the Installer Code + 8 8 8. When you have completed each programmi

Comments to this Manuals

No comments

Lynx Dollhouse 1000-300-011-V0 User Manual

Browse online or download User Manual for Motion detectors Lynx Dollhouse 1000-300-011-V0. Lynx Dollhouse 1000-300-011-V0 User's Manual

Summary of Contents

Comments to this Manuals